Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
What are your ideas regarding How to Install a Bathtub?
Installing a bath tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably tough job. If the old bathtub is conveniently available, the job can move speedily; if you have to open up a wall surface to eliminate the old tub as well as position the new bath tub, the job is much harder. In either case, the task is within a home handyman's skills, although you will need an assistant to leave the old tub as well as embeded in the brand-new one. See to it you have actually qualified on your own for the job as well as are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly assist you install a new bath tub in your washroom if you have already gotten a brand-new bathtub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and also material checklist need to make up the following:
Getting ready for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, position the bath tub in the required position. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; then do the same for the other faucet.
Activate the water system and inspect all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill the tub as well as likewise inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub should wait up until the tub has been utilized at the very least when as this will certainly settle it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers remain in location in between the tap and the sink. Protect the tap in place with the supplier offered backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap adapters. The former kind needs to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in issues with moisture as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealer can break fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub? Give a review below. We will be interested to listen to your views about this blog post. In hopes that you come back again soon. Sharing is nice. One never knows, you will be doing someone a favor. Thank-you for your time spent reading it.
Got trouble? Ring! Report this page